17 Reasons You Shouldnt Be Ignoring Repairs To Upvc Windows

Repairs to uPVC Windows
uPVC is a great choice for modern homes. They are long-lasting, durable and easy to maintain. Unlike timber and aluminium, they don't get rusty or decay.
It is crucial to wash and oil UPVC doors and windows regularly. This will help prevent costly repairs and increase energy efficiency.
1. Broken Glass
The damaged glass in your windows can cause serious damage to your home, and could even be fatal. It is essential to make sure that your windows are in good working order.
For single pane windows, it is fairly easy to replace windows, and the new one will usually fit inside the frame that was previously installed easily. However, if windows with double panes are anchored by internal beading it will be more difficult to get rid of the existing panes and install new ones. In this instance you'll need to locate some plastic spacers to assist the new pane to fit properly into the frame of the window.
Wearing eye protection and heavy gloves is essential for anyone who plans to remove the glass by yourself. You should also lay down a dropcloth before you begin working on the window panes to ensure that any shards of glass fall onto the fabric and not onto the floor, where they could be trampled under.
Internet Page 's a good idea to cover the gap with tape after the glass is removed. This will prevent drafts and water from getting into your property until a professional is able to fix the window. It also acts as a barrier that will prevent any intruders from gaining entry into your home. If the gap is particularly large, you may think about an alarm door that comes with an integrated window, as it will provide the best of both worlds.
2. Sagging
uPVC windows and doors are a cost-effective, durable and energy-efficient alternative to timber windows with sash. However, over time, they can suffer from a variety of problems including sliding. A sagging window can cause problems with light, draughts and even security. If you find that your uPVC window is beginning to sag it's crucial to act fast to stop the issue from getting worse.
To fix a window that is sagging you can try repositioning the hinges. To do this, you'll have to open the window so that you can get to the frame. Then, using a screwdriver, you can remove the hinges at the top and bottom and adjust them by turning them clockwise or anti-clockwise. Close your window to check the fit after you have relocated your hinges. If you are happy with the fit of the window, you can tighten screws to hold them in place.
If you are unable to move the hinges, you may need to replace the seal. Over time rubber seals can lose their elasticity and dry out, which causes them to lose tightness. If this happens, it's important to replace the seal as soon as possible so that your uPVC windows remain watertight and secure from draughts.
uPVC handles could also loosen. This is typically caused by screws that have become undone over time, but it can also be caused by the handle mechanism wearing out. Luckily, it's not difficult to repair the handle of a window that is loose yourself. First, you'll need to shut the window and perform a test fitting. The corners of the sash should be aligned with the casing joint. If it doesn't you can use a screwdriver to loosen the handle. Then, you can turn the mechanism back into place.
3. Water Leaks
It is essential to take action if you awake each day to find a smoky wall and wet floors. Water leaks from windows are not just a cause for destruction of your home's structure but also hamper your efforts to control the temperature within your home. The most frequent reason for leaking uPVC windows is that the sealant around the frame is damaged or missing.
This is a relatively easy fix that can be done by any skilled DIYer. Based on the severity of the issue the caulking used previously may need to be removed before a fresh layer is applied. It is important to remember that when it is about uPVC window repairs, you should not be tempted to 'over-caulk in order to make the area more difficult to clean and can reduce your energy efficiency.
It is essential to ensure that the drainage holes are clear of debris and that the sill pan is angled in a way that allows it to drain away from the window. In more severe situations, you may have to replace the window.
Other indicators of water leakage are decayed sills and the appearance of black spots of mold on the walls near the window. This fungus thrives under conditions of dampness and can spread quickly throughout the house.
If the leakage is occurring between the double-glazed glass, it is more likely the issue is with the seal rather than the frame. A uPVC specialist can fix this problem by replacing the glass seal. This will ensure the complete insulation of your windows.
4. Faulty Hinges
Hinges could be at fault when your uPVC window is difficult to open or if it blows open with the breeze. They can be easily replaced by any competent DIYer and are usually done within a few minutes.
Like any mechanical component, hinges can be damaged over time. The process of replacing a hinge on a window is an easy procedure, but it is simpler if you have someone to help hold the frame in place.
Make sure that the uPVC hinges are open and closed in the right direction. You can do this by looking for the arrows on each hinge. This indicates which way the window should be opened.
The issue could be caused by opening the window improperly or a faulty installation in the factory. This can often be resolved by sending us a photograph via our website and we will be happy to give you advice.
It is also crucial to grease the hinges on a regular basis. Applying a light engineering lubricant to the hinges is an ideal method to accomplish this. We suggest using an oil that does not contain solvents, such as 3-in-1 Multi-Purpose oil. Regular lubrication will make the window easier to open and close. It also helps prevent corrosion and reduce the possibility of sticking. It is recommended to do this at least once a year. WD40 or other solvent-based oils should not be used as they can damage your uPVC windows.
5. Draughts
Draughts can be caused by different causes. The hinges can also be misaligned due to wear, causing an opening where the sash and frame meet. If they are damaged beyond repair, it might be necessary to get them re-aligned. The interlock, which is located on the hinge of the window and can also be misaligned, and again it's possible to just give them a good clean, but in certain cases, it may be necessary to have them replaced.
These seals can wear down or be damaged over time, allowing air escape. Replacing these with high-quality weatherstripping will help to prevent draughts. Replace the upvc windows with low-emissivity glass. This will help to regulate indoor temperatures and decrease the risk of draughts.
Another method of reducing the amount of draughts is to use a Draught-excluder. These are usually fabric tubes filled with a filler that can be hung over your window sill. They can help block out cold air and keep your home warm and cozy!
The windows made of upvc can continue to provide excellent insulation and security to your home with regular maintenance and repairs. It is essential to remember that all windows eventually wear out and it could be more cost-effective to replace them rather than repair them. If you are experiencing issues with your Upvc window you should consult an expert as soon as possible.