11 Strategies To Completely Block Your Repairs To Upvc Windows

Repairs to uPVC Windows
uPVC windows are a great choice for modern homes. They are easy to maintain, durable and long-lasting. As opposed to aluminium and timber they don't get rusty or decay.
Regularly cleaning and lubricating UPVC windows and doors is essential. This will help prevent costly repairs and increase energy efficiency.
1. Broken Glass
If the glass in your window has been damaged, it can cause a huge amount of damage to your home, which can make it extremely dangerous and possibly fatal. You should take the time to ensure that your windows are in good working order.
For single pane windows it is relatively easy to replace windows, and the new one will usually fit inside the frame of the previous one easily. However, if you have double-pane windows that are held in place by internal beading, it will be more difficult to get rid of the old panes and put in new ones. In this case, it is necessary to purchase plastic spacers in order to help the new pane fit into the window frame.
Wearing eye protection and thick gloves is a must for anyone who plans to remove the glass by yourself. It is also recommended to lay down a dropcloth before you begin working on the glass to ensure that any fragments of glass fall onto the fabric instead of landing on the floor where they can be trampled upon and cause further damage.
Once the glass has been removed from the window, it's best to cover the gap with some clear packaging tape or duct tape to prevent drafts and water from entering the home until a professional comes out and fix the window. This also serves as an obstacle to stop intruders from getting into your home. If the distance between the window and the door is large, you might prefer an alarm system that has windows. This will give you the best of both.
2. Sagging
uPVC is durable and energy efficient alternative to timber sash windows. However, with time, they can suffer from a variety of problems including sliding. A sagging uPVC window can cause issues with light, draughts, and even security. If you notice that your uPVC window is beginning to sag it is important to act swiftly to prevent the problem from worsening.
To fix a window that is sagging you can try to reposition the hinges. You'll first need to open the windows so you can reach the frame. Then, using a screwdriver, you can take off the hinges at the top and bottom and adjust them by turning them clockwise or counter-clockwise. Close your window to test the fit after having repositioned your hinges. If you're satisfied with the fit of the window, tighten the screws to keep them in place.
If you are unable to reposition the hinges, you could need to replace the seal. Rubber seals can dry out and lose their elasticity with time, which causes them to loosen. It is important to replace your seal as quickly as you can in order to keep your uPVC window waterproof and draughtproof.
uPVC handles can also loosen up. The majority of the time, this is caused by screws that have become loose over time. However, it could also happen because the handle mechanism has been worn out. It's a good thing that it's simple to repair a loose uPVC window handle yourself. The first step is to close the window and then perform an initial test to ensure that it fits. The joint at the corners of the sash should be aligned with the joint on the casing. If it doesn't then you can use a screwdriver to loosen the handle and then turn the mechanism back into position.
3. Water Leaks
It is crucial to act if you wake up every morning to find a smoky wall and wet floors. Water leaks through windows can cause structural damage to your home and also impact your ability to regulate the temperature of your home. The most common cause for leaks in uPVC windows is that the sealant surrounding the frame has been damaged or not present.
This is a fairly simple fix that can be done by any competent DIYer. Depending on how serious the issue is, the old caulking may need to be removed. It is important to keep in mind that when it comes to uPVC window repairs , you should not be tempted to apply too much caulk in order to make the area more difficult to clean and reduce your energy efficiency.
Make sure that the drainage holes have no debris in them, and also that the sill pan has been properly angled to allow the water to drain from the window. In more serious instances, you might have to consider replacing the window.
Other signs of long-term water leakage are sills that are rotten and the appearance of black spots of mold on the wall near the window. The fungus thrives in damp conditions and can quickly spread throughout the home.
If the leakage is occurring between the double-glazed glass it is more likely the problem is with the seal rather than the frame. A uPVC specialist can easily fix this problem by replacing the glass seal. This will restore the full insulation of your windows.
4. Faulty Hinges
If your uPVC windows are difficult to open, or loose and blow open with a breeze, it may be hinges that are at fault. Anyone with the skills to fix them can replace hinges in just a few minutes.
Like all mechanical parts, hinges can be damaged over time. It is essentially a very simple procedure, but it is easier to do when you have a person to assist in holding the frame in place.
It is also important to verify that the uPVC hinges are opening and closed in the right direction. Look for the arrows on each hinge to determine the direction in which the window should be opened.
The problem can be caused due to opening the window in the wrong way or a faulty installation in the factory. Sending us a photo through our website can often resolve the problem. We are happy to give suggestions.
Regular lubrication of the hinges is also necessary. Applying an engineering lubricant that is light to the hinges is an ideal method of doing this. We recommend using the lubricant that doesn't contain solvents, such as 3-in-1 Multi-Purpose oil. Regular lubrication will make the window easier to open and close. It can also prevent corrosion and reduce the risk of sticking. This should be done at least every year. WD40 and other solvent based oils are not recommended because they could damage parts of your uPVC window.
5. Draughts
Draughts in Upvc windows can be caused by a variety of different factors. First, the hinges because of wear and tear, could become misaligned. This causes an opening to appear where the sash joins the frame. This can be easily fixed by giving them a good cleaning, but if they are beyond repair it could be necessary to get them re-aligned or replaced. The interlock may also become unbalanced. It is located on the hinge's side, and may need to be cleaned. In some cases, it may be necessary to replace these.
These seals are susceptible to wear and tear or get damaged over time, allowing air to escape. This can be prevented by replacing them with high-quality weatherstripping. Replace the upvc windows with low-emissivity lenses. This will help regulate indoor temperatures and lessen the possibility of draughts.
The last way to reduce the amount of draughts is to use a draught-excluder. These are usually fabric tubes filled with a filler that can be hung over your window sill. These will keep your home warm by blocking out cold air.
With a little regular maintenance and repairs windows made of upvc will continue to provide excellent insulation and security for your home. However, it is important to recognize that all windows have a life span and they may reach an point at which it is more economical to replace them than fix them. So, if you are experiencing problems with your upvc windows, it's best to seek professional assistance as soon as you can.